TM9x52-62CII0 pages
TERMOREGOLATORE PROGRAMMABILE
PROGRAMMABLE TEMP. CONTROLLER
•
•
•
•
•
•
•
•
TM9X52 :48X48mm (1/16 DIN) TM9X62 :48X96mm (1/8DIN)
DOPPIO DISPLAY 4 CIFRE. 4 TASTI. 4 O 8 LEDS. DOPPIA CHIAVE
MULTIINGRESSO. MULTIFUNZIONE. COMPLETAMENTE CONFIGURABILE A TASTIERA.
SET 1 / SET 2 - SET POINT REMOTO. SELEZ. LOC / REM
SELF TUNING , AUTO TUNING , MAN/AUTO , ECONOMY , RAMPA , ...
TRE USCITE : MAIN , LIMIT I , LIMIT II .
RITRASMISSIONE SEGNALE - COMUNICAZIONE SERIALE RS232 O RS485
DISPONIBILE VERSIONE PROGRAMMATORE 10 PROGRAMMI 100 SPEZZATE TOT.
♦
♦
♦
♦
♦
♦
♦
♦
TM9x52-62
TM9X52 :48X48mm (1/16 DIN) TM9X62 :48X96mm (1/8DIN)
DOUBLE DISPLAY 4 DIGITS. 4 KEY BOARD. 4/8 LEDS. DOUBLE KEY.
UNIVERSAL INPUT. MULTIFUNCTION. PUSH-BUTTON SET-UP.
SET 1 / SET 2 - REMOTE SET POINT
LOC / REM SEL.
SELF TUNING , AUTO TUNING , MAN/AUTO , ECONOMY , RAMP , ...
THREE OUTPUTS : MAIN , LIMIT I , LIMIT II .
RETRANSMITTED SIGNAL - SERIAL COMMUNICATION RS232 OR RS485
PROGRAMMER VERSION AVAILABLE 10 PROGRAMS 100 STEPS TOT.
GENERALITA’
TM9x52-62 è un regolatore completamente configurabile da tastiera.
E’ possibile selezionare tipo ingresso (termocoppia / termoresistenza
/ segnali da campo), scala, offset, parametri di regolazione, ecc....
Il display è ben visibile anche a distanza grazie ad un apposito filtro
ottico ed a cifre alte 10mm per il display principale (orange alta
efficienza) e 7 mm per il display secondario (verde alta efficienza).
Sviluppato per svolgere funzioni di regolazione e controllo in
applicazioni di riscaldamento , refrigerazione e generiche , è in grado
di soddisfare le più disparate esigenze sia per la completezza delle
funzioni offerte , sia per il numero di uscite e ingressi disponibili.
Disponibile uscita analogica ausiliaria indirizzabile su variabile scelta
o comunicazione seriale (RS232 o RS485) protocollo Modbus RTU .
Possibili fino a due (2) ingressi digitali con azione programmabile.
Esiste versione programmatore di spezzate (relazione tempo-temp.)
con possibilità di 10 programmi per un totale massimo di 100 passi.
In tal caso gli allarmi possono essere impiegati come relè di passo.
Con uscita continua può essere impiegato come generatore di Set.
CARATTERISTICHE PRINCIPALI
Operatività ed interfaccia uomo/macchina sono basate su menù.
La struttura dei menù è relazionata alle funzioni ed alle impostazioni.
Nel gruppo ‘SetP’ sono possibili le impostazioni di Set-Point Main ,
Set2 (secondario), Set Limit I (allarme 1), Set Limit II (allarme II),
Set-Point Remoto e relativi parametri di inizio e fondo scala.
Nel gruppo ‘Out’ sono accessibili tutti i parametri inerenti il
regolatore principale ed oltre ai parametri classici quali PB, dt, it,
ct è possibile impostare il funzionamento Manuale/Automatico, la
potenza in uscita, l’ArS (Anti Reset Window), il modello di
autosintonizzazione (SelfTuning o Autotuning), la limitazione di
potenza (MPo-->Economy), il comportamento in presenza di
overrange (P.ovr) od underrange (P.und), la funzione dell’allarme I
scegliendo tra ben 37 diverse possiblità. Tra queste è possibile
sceglierne l’impiego come raffreddamento, con azione ON/OFF
oppure PID ed anche qui oltre ai parametri PB, dT, It, ct è possibile
determinarne il comportamento con la banda di sovrapposizione, il
mezzo (aria, olio, acqua), il guadagno del loop ed infine la funzione
dell’allarme II scegliendo tra altre 36 diverse possiblità.
Nel gruppo ‘A.Out’ (Auxiliary Output) sono disponibili le impostazioni
relative alla comunicazione seriale (protocollo, indirizzo, baud
rate, selezione LOC/REM e ritardo) ed all’uscita analogica
ritrasmessa (sorgente, relazioni ingresso/visualizzazione,
comportamento in corrispondenza di min.,max, O.ovr e o.und).
Da sottolineare la possibilità scegliere di ritrasmettere la variabile di
ingresso oppure uno dei Set-Point o la potenza od il display.
Nel gruppo ‘A.InP’ è possibile determinare il comportamento degli
ingressi digitali 1 e 2 (blocco tastiera, hold misura, Set/Set1/
SetRem, Loc/Rem, Start/Stop/Reset per programmatore)
e dell’HbM (Heather break Monitor) con relativi parametri.
Nel gruppo ‘dISP’ si può impostare il comportamento del display ed in
generale dell’interfaccia uomo/macchina coi parametri offset, chiave
di protezione a tre livelli, timeout, memorizzazione parametro,
selezione °C/°F, posizione punto decimale.
Nel gruppo ‘ConF’ deve essere scelto l’ingresso con inerenti
relazioni, il filtro letture, la chiave di protezione numerica.
Infine nel menù ‘ProG’ si trovano i numerosi parametri riguardanti la
versione PROGRAMMATORE (vedi manuale corrispondente).
GENERAL DETAILS
TM9x52-62 is a keyboard fully configurable controller.
It’s possible to select input type (thermocouple / thermoresistance /
signals from the field), scale, offset, control parameters, etc. ....
The display is clearly visible from distance thanks to the optical filter
and the size of the digits; 10mm for the main display (high efficiency
orange) and 7mm for the secondary display (high-efficiency green).
Developed to perform regulation and control in heating, refrigeration
and generic applications, it is able to satisfy the various
requirements by the completeness of the offered features
and thanks to the available number of outputs and inputs.
It can be with auxiliary analog out addressable on selected variable
or serial communication (RS232 or RS485) Modbus RTU protocol.
Up two (2) digital inputs with programmable action.
It’s obtainable in ‘step-programmer’ version (time-temperature
relationship) with 1 to 10 programs for a maximum of 100 steps.
In that case, the alarms can be used as step relay.
With continuous output can be employed as a master Set.
MAIN CHARACTERISTICS
Operativity and man / machine interface is based on the menu.
The menu’s structure is related to the functions and settings.
In group ‘SetP’ are possible settings of Set-Point Main, Set 2
(secondary), Set Limit I (alarm 1), Set Limit II (alarm II),
Remote Set-Point and its related parameters (i.e. start and full scale).
In group ‘Out’ are available all the parameters relating to the
main controller and in addition to classical parameters
such as PB, dt, it, ct can be set Manual / Automatic action,
Output Power, the ArS (Anti Reset Window),
the tuning model (SelfTuning or Autotuning), the power limitation
(MPo -> Economy), the behavior in case of overrange (P.ovr) or
underrange (P.und), the function of the alarm I choose between no
less than 37 lots of possibilities.
Among these you can choose the job as a cooling action with
ON/OFF or PID parameters and even here in addition to PB, dT, It, ct
can determine the behavior with the overlap band, the medium (air, oil,
water), the gain of the loop and finally the alarm function II,
choosing from 36 different other possibilities.
In group ‘A. Out’ (Auxiliary Output) is available settings for
serial communication (protocol, address, baud rate, selection
LOC / REM and delay) and analog retransmitted output (source,
input/display relationship, behavior for min., max, O.ovr and O.und
correspondence).
Significative the possibility to choose to retransmit the variable input or
one of the Set Point or the output power or the display.
In group ‘A InP’ you can determine the behavior of digital inputs 1
and digital inputs 2 (keylock, measure hold, Set/Set1/SetRem, Loc/
Rem, Start/Stop/Reset for programmer) and HbM (Heather break
Monitor) function with related parameters.
In group ‘dISP’ you can set the display behavior in general and of
man/machine interface with the parameters offset,
three level security key, timeout, storage, °C / °F selection, the
decimal point position.
In group ‘ConfF must be chosen the input with related reports, the
reading filter, the security numeric key.
Finally, in the ‘ProG’ menu you can find the great number of parameters
for the PROGRAMMER version (see its manual).