PTU2 27/27 DIESEL0 pages
PTU2 27/27
CJC™ Filter Separator - D I E S E L
CJC™ Product Sheet
APPLICATION
The CJC™ Filter Separator PTU2 27/27 Diesel is used on
diesel oils with a specific weight lower than that of water.
The PTU2 27/27 is ideal for separation of water, removal
of particles and degradation products.
FUNCTION
The filter pump draws oil from the settling/bunker tank and
presses it through the filter insert. From the centre of the insert the oil flows down into the filter base where water droplets adhere to the coalescer element, forming larger drops that
will settle in the bottom of the filter base. From the top of the
filter base the oil will flow to the service tank or back to the
settling/bunker tank.
The filter suction pipe should be connected to the bottom of
the settling/bunker tank, above the tank drain tap. The filter
outlet should be lead to the service tank.
An overflow line from the top of the service tank back to the
settling tank should be applied in order to secure that surplus
oil flows back to the settling/bunker tank.
On the PTU with automatic water discharge, separated water
is drained automatically. The discharge function can be monitored on the unit control box. The PTU models are also available with manual water discharge.
The pressure drop over the filter - and consequently the contaminant absorption of the filter insert - is monitored on the
pressure gauge on the filter top.
THE FILTER PUMP
The CJC ™ Filter Separator
PTU2 27/27 PV-E2W
The filter pump is a CJC gear wheel pump. The electric motor
can be supplied for all standard AC and DC voltages.
FILTER INSERT
The CJC™ Filter Inserts consist of several discs bonded together. The material is either cellulose or cotton linters depending on the fluid to be filtered.
OPTIONS
Preheater
Drip pan
Control box
Tank
Automatic water discharger
TECHNICAL DATA
PTU2 27/27
Model PTU2 - DIESEL
Pump flow, per hour (std.)
PV
ltr/gal
Pump type
Pump inlet pressure, max.
pcs.
1
kW
Water Removal by Separation
The CJC™ Filter Separator removes water from oil to very
low levels. The efficiency of water removal depends on the
oil type and temperature.
Particle Removal
All CJC™ Filter Inserts have the following filtration
degree:
- 3 μm abs.: 98.7% of all solid particles >3 μm
- 0.8 μm nom: 50% of all solid particles >0.8 μm
are retained in each pass.
The dirt holding capacity is 4 litres of evenly distributed solids.
Degradation Products
Oxidation products, resin / sludge, and varnish are
retained by the cellulose material, which will retain
appr. 4 kgs of oil degradation products.
Preheating the oil before filter pass may be necessary to prevent segregation of paraffin, but only with blended fuels.
PSST1011-UK
09.04.2008
Page 1/2
P
bar/psi
0.18
Power consumption, aver.
PV/P-E2W
45 - 200 / 12 - 53
PV4
Filter Inserts 27/27, std.
FILTRATION ABILITY
P
PV / P
0.5 / 7
1
1
0.25
0.25 - 0.40
Pressure drop, max.
bar/psi
1.8 / 26
1.8 / 26
Oil temperature, max.*)
˚C/˚F
60 / 140
60 / 140
Dirt holding capacity, appr.
ltr/gal
4 / 1.1
4 / 1.1
Dry weight
kg/lb
78 / 172
90 / 198
Operating weight, wet
kg/lb
90 / 198
102 / 224
Design pressure, filter
bar/psi
4 / 58
4 / 58
Ambient temperature, max.
˚C/˚F
40/104
40/104
Manual
Automatic
Water discharge
*) The standard filters are designed for a max. temp. of 60˚C/140˚F.
Other conditions, please contact us.
APPLICABLE FILTER INSERTS
Type
Application for
F:
Low flow.
BLAT:
High flow.
"