IO-CB series0 pages

Canbus-analogue-inst-e

28-01-2010

ISO9001 Certified

11:33

Pagina 1

CANopen Analogue
I/O Modules

mod. IO-CB
M.I. IOA-CB-1/06.06
Cod. J30-658-1AIOA-CB E

Installation
Manual
ASCON spa
20021 Baranzate (Italy)
Fax +39 02 350 4243
www.ascon.it
sales@ascon.it

IO-CB/AI-02UI:
IO-CB/AI-04RT:
IO-CB/AI-08DP:
IO-CB/AI-08HL:
IO-CB/AI-08TC:
IO-CB/AO-08DP:
IO-CB/AO-08HL:

Contents
- General description
- Accessories
- Installation
- Electrical connections
- Electric safety

E

2 Isolated Analogue Inputs
4 Configurable Analogue Inputs
8 Voltage Analogue Inputs
8 Configurable Analogue Inputs
8 Thermocouple Analogue Inputs
8 ±10V Output Channels
8 High Level Analogue Inputs

General description

Installation
Dimensions (mm)

Operating conditions
Environmental condition

7

6

70

64

Operating
conditions

110
8 LO
8 HI
5

9

46
76/152

45

1
66

10

2

40

Additional terminal block

Special
conditions

22

11

Forbidden
conditions

48

3

- Mount the module vertically
- In order to help the ventilation flow of
air, respect the distances between
modules and walls or other modules.

1
2
3
4

- Model identification label (on the back side of the module)
- DIN RAIL 35 x 7.5 (EN50022)
- 2 male 11 pole plugs, pitch 5.0mm
- 2 + 2 female, 11 pole, fast snap-ON connectors, pitch 5.0mm, with screw or
spring terminals to connect the power supply or the I/O (accessory)
5 - Two RJ45 plugs to connect the field bus
6 - CANopen cable with two RJ45 connectors (accessory)
7 - RJ45 plugs with internal termination circuitry (accessory)
8 - 2 rotary switches having 16 positions to set Node ID and Baud rate
9 - Removable and writable label to identify the connected I/O (TAG number)
10 - 4 status LEDs: identify the diagnostic and the module status
11 - Additional terminal block 2 x 11 poles (accessory)

min. 80

Mounting
position (mm)

Use forced
ventilation

Temperature
> 65°C

%Rh > 95% RH

Warm up

P Conducting
atmosphere
C Corrosive
atmosphere

Use filter

E Explosive
atmosphere

Mounting/removing the modules
on/from the DIN rail

Mounting position
4

%Rh Umidity 5...95% Rh
non condensing

T

21

Rail mounting
DIN 35 x 7.5
(EN 50022)

T

B Suggestion

Temperature
-10...+65°C

min. 60
64

1 Close the spring slide, then clip the upper
part of the module on the rail
2 Rotate the module downwards till to the click
3 Switch OFF the Power Supply
Lower the spring slide by inserting a flatblade screwdriver as indicated
4 Turn and lift the module upwards.
Mounting the module
2

1

CLICK
min. 100

Removing the module

3

4

Hot swapping the modules

Accessories
Power supply 45W - 2A/24 Vdc

11 poles connectors

Field bus cables with RJ45 connectors

AP-S2/AL-DR45-24

With screw terminals: AP-S2/SPINA-V11
With spring terminals: AP-S2/SPINA-M11

140 mm: AP-S2/LOCAL-BUS76
220 mm: AP-S2/LOCAL-BUS152

Power supply 120W - 5A/24Vdc

Additional terminal block

2 connectors with termination circuitry

AP-S2/AL-DR120-24

AP-S2/TB-211-1

AP-S2/TERM-CAN

Node ID and Baud rate of the new module
must already be correctly set.
The procedure to minimize the MODBUS
disconnection time follows:
1 Remove all the cabled connectors from
their plugs (item 4 in “General description” paragraph), do not extract the
MODBUS RJ45 connectors yet
2 Remove the module from the DIN rail
3 Mount the new and already configured
module on the DIN rail
4 Extract the left side RJ45 connector from
the module and insert it in the new module
5 Extract the right side RJ45 connector from
the module and insert it in the new module
6 Insert all the cabled connectors in the new
module.