Model M1434E Maxiflex 8AI ISO module0 pages
MAXIFLEX 8AI ISO Module
Model M1434D Individually Isolated 8 way High Accuracy Analogue Input Module.
DATASHEET
FEATURES
•
Fits in any MAXIFLEX base I/O slot
•
8 individually isolated configurable analogue Inputs
•
Full inter-channel isolation for industrial applications
•
24 bit measurement resolution for very high accuracy
•
milliVolts/Volts and Currents individually selectable on
each input allows mixed types and ranges.
•
Four Alarm/Trip setpoints per input.
•
Removable Terminal Blocks
•
Hot Plug-in
•
In system automatic module detection
DESCRIPTION
The M1434D 8AI ISO module provides 8 inputs that
can be individually configured for millivolts/Volts or
Current inputs. The inputs are individually isolated. This
intelligent module is software configurable, and allows
each input to be configured for a different input type
and range. The input value can scaled in the module
into Engineering Units of the user’s choice
Current inputs are measured using an internal 220 Ohm
resistor switched in across the input terminals.
Each input has four software settable alarm/trip
setpoints and a deadband value. The status of the
alarm/trip signals is available as derived digital inputs
from the module.
The module may be inserted into any I/O slot in a
Maxiflex system.
Inputs are terminated on plug-in screw terminals.
The module can be inserted or removed while the
system is powered.
Auto-detection capability allows the CPU to recognise
the presence of this module in the system.
All configuration and dynamic data are made available
to the system CPU through the module registers. The
module is configured by writing the appropriate values
to these registers, and the dynamic values are read by
reading from these registers.
SPECIFICATIONS
Inputs
Output Termination
Quantity
8
Voltage range
-0.1000000 to 5.125000V
Types
Screw clamp Plug-in Terminal
Blocks and 20 way ribbon header
Current range
-0.500000 to 23.300000 mA
Screw Terminal Wire Size
2.0mm2 maximum
For manageable wiring to the
module, 0.5 mm2 is recommended
with 2mm overall outside diameter
Input Resolution
1microVolt or 1microAmp
Input Impedance (Voltage)
1MΩ
Input Impedance (Current)
220Ω
Environmental
Linearity
0.01% of span max.
Operating Temperature
0°C to +60°C (32°F to +140°F)
Temperature Drift
50ppm/°C typical
Storage Temperature
-40°C to +85°C (-40°F to +185°F)
ResponseTime 10-90% step
Settles to within 3% in 200ms
Humidity
5 - 95% max. at 40°C (104°F)
non-condensing.
Input to system logic
100% tested to 1500Vac rms (60s)
Protection
Electronics conformally coated
Input to Input
100% tested to 500Vac rms (60s)
Logic Power Consumption
Insulation resistance
>20MΩ at 500Vdc
From Logic Power Supply
Isolation
300mA max from 5Vdc
Mass
Interference Rejection
CMRR at 50/60Hz
120dB at 250Vac rms
Excluding Packaging
420g (14.7oz)
NMRR at 50/60Hz
50dB at 250 Vac rms
Including Packaging
505g (17.8oz)
Ordering Information
LED Indication
CPU OK
ON = operating correctly
Flashing = Module failure
OFF = No Power or module failure
Description
Order Code
Maxiflex 8AI ISO Module
M1434D
Copyright Omniflex ♦ Subject to change without notice
Datasheet DSC1434DR03 sheet 1 of 2
http://www.omniflex.com
®
"