Digital Torque Meter0 pages

"Digital Torque Meter (2) TS-2700

Output Section >

nnGeneral Type of Compact Torque Converter with Digital Display, Suitable for Panel Mounting

■ Analog Voltage Output Section Torque output level:0 to 10V/FSRevolution output level:0 to 10 V/FSTime constant:Torque: 500 ms/63 ms Revolution: 63 msAccuracy:Torque: ѱ 0.2%/FS (when N-0 compensation is used)Revolution: Torque Measurement Section ■ Input Section 0.1%/FSIsolation:Withstand voltage of 250 VDC for one minuteCOMMON is the same for torque and revolution.Proper load:10 k Input signal:Phase-differential type detector output signalMatching connector:TRC116-12A10-7M10.5 Ѣ֠ Setting Section Ω or moreMatching connector:C02 type (BNC) Zero compensation:1 point each for CW, CCW, push-button setting of auto-zeroN-0 compensation:5 points each for CW, CCWZero switching:CW, CCW, EXT.Decimal point lighting:Automatic ■ Display Section Numerical value display:7-segment green LEDsDisplay range:-9999 to +9999Display unit:Nm (mN׷m, kNm are also available by using the accessory seals.)Display switching interval:1 s/10 s/EXTAccuracy ( 1-s averaged values):With N-0 compensation; ע֠ Digital Output Section Output format:BCDOutput renewal:Every 1 sMatching connector:DX40-50P >

nn

The TS-2700 can provide a digital display of the measurement data while outputting the data to an external device using analog voltage, BCD or RS-232C outputs. Being compact in size, it does not take up much space when mounted in an instrumentation panel. It can also be accommodated neatly adjacent to a control device inside the panel. The display units are Nm, and r/min, but other units can also be specified by using the accessory unit seals.

ע֠ RS-232C (refer to the chart below.) Transmission speed:9600 bpsFunctions:Input of zero value, N-0 value, and settings; output of measured values and setting conditionsCompatible cable:AX-5022 ѱ 0.2%/FS 0.5%/FS ѱ 1 count Without N-0 compensation
; 1 count Revolution Measurement Section ■ ■ Input Section >

nn

Other functions:

1. REV IN.Output signal from Ono SokkiŒs MP-981 electromagnetic type revolution detector Input frequency range:1 Hz to 100 kHz (accuracy guaranteed from 10 Hz) Matching connector:R03-PB6M2. INT.Ņ..Used for SIG2 torque signals >

nn

● ● N-0 compensation function: Inputting the N-0 compensation value enables a torque measurement accuracy of Remote control functions: External switching of rotation direction setting, changing the BCD data switching interval (100 ms to 64 s), synchronized driving of two TS-2700 units, safety interlock using measurement preparation complete signal outputs are possible.

Remote functions (refer to the chart below.) >

nn

0.2% of full scale.

Input:CW, CCW switching, clear input, trigger inputOutput:Trigger output, measurement preparations complete signal output >

nn

Ѣ׏ CW/CCW switching: The settings of both rotation directions are stored in an internal non-volatile memory to enable them to be switched.In order to supply the suitable cable which can withstand the power supply to this unit, please specify the electrical power voltage when ordering.

General Specifications Power supply voltage:100 to 240 VAC, 50/60 HzPower consumption:Approx. 25 VA (100 VAC)Insulation resistance:10 M ■ Setting Section Number of detector pulses:1 to 9999 P/R ■ Display Section The numerical value display unit and the display switching interval are the same as those given in the Torque Measurement Section.Display range:Up to 99999Display unit:r/min
Accuracy (1-s averaged values): Ω min. at 500 VDCWithstand voltage:1500 VAC for one minuteOperating temperature range:0 to +40 >

nn

Notes:
Specifications

0.02%/FS ѱ 1 count CStorage temperature range:-10 to +55 а CWeight:Approx.1.8 kg
Accessories:Display unit seals x 1 setMatching connector for remote control x 1 setRubber foot x 4 pcs.
Power cable (1.9 m) x 1 pc.
Instruction manual x 1 copy >
2 −φ 4 READY TRQ REV MEAS CAL CW CCW MEAS/CAL LOCK CW/CCW TRQ ZERO 134142 126 MENU POWER ENTER TS-2700 Torque Converter 76 (13)302(6)

nn■ RS-232C Pin Assignments Recommended interface nn

PinSignal name1 2RxD (Receive Data)
3TxD (Transmit Data)
4CTS (Clear to Send)PinSignal name5 RTS (Request to Send) 6֖
7SG (Common)
8 TRQ IN REV IN TS-2700 output+5VRLRLORCOMMON
+48V or lessExternal device+5V REMOTE TRQ OUT 0.5127 BCD OUT ֱ

nn■ Remote Function Pin Assignments nn

REV OUT 134 PinSignal nameRemarksACLR IN
BTRG INCCW/CCW switching
DCOMEREADY OUTFDitto COM-1GTRG OUTHDitto COM-2 RS232C Non-voltage contact input
(COMMON is common)Non-voltage contact output(COMMON is separate) MADE IN JAPAN Load voltageAC/DC 48V maxLoad current100mA max
On resistance10 Ω max.Off resistance500 k 73 752-M3 Ω min. Panel Cutout DimensionsRear View
Side ViewFront View >

nn

13

"