عضویت 
ورود اعضا
راهنمای خرید
SH Shaft Rings0 pages
SH Shaft Rings
nnnnAxially Assembled, External
nnnnOnce installed in the groove of a shaft, the portion of the ring
nnnnprotruding from the groove (also called a "shoulder")
nnnnholds an assembly in place.
nnnnS min
nnnnFree Diameter & Ring Measurements
nnnnwith Section B-B
nnnnShaft Diameter &
nnnnGroove Dimensions
nnnnClearance Diameter
nnnnExpanded Over Shaft
nnnnClearance Diameter &
nnnnGaging Diameter
nnnnReleased in Groove.
nnnnRING un NU. | SHAFT DIAMETER | GROOVE SIZE | RING SIZE & WEIGHT | CLEARANCE DIA. | 1 THRUST LD.(lbs.) Sqr. Corner Abutment | ||||||||||||
DIAMETER | WIDTH | ucr i n | FREE DIAMETER | THICKNESS*** | Per 1000 pes. | LA nnnripri over Shaft | Re nc- IP a SPrl in Groove | ||||||||||
Ring Safety Factor of 4 | Groove Safety Factor ot2 | ||||||||||||||||
lie us DEC | us FRAG | ric us rnm | |||||||||||||||
Da | Tol. | W | Tol. | d | Df | Tol. | T | Tol. | lbs. | L1 | L2 | Pr | Po | ||||
**SH-12 | .125 | 1/8 | 3.2 | .117 | ±.0015 .0015* | .012 | + .002 -.000 | .004 | .112 | + .002 -.004 | .010 | ±001 | .018 | .222 | .214 | 112 | 35 |
**SH-15 | .156 | 5/32 | 4.0 | .146 | .012 | .005 | .142 | .010 | .037 | .27 | .260 | 132 | 55 | ||||
**SH-18 | .188 | 3/16 | 4.8 | .175 | .018 | .006 | .168 | .015 | ±.002 | .059 | .298 | .286 | 244 | 80 | |||
"SH-19 | .197 | 5.0 | .185 | .018 | .006 | .179 | .015 | .063 | .319 | .307 | 254 | 85 | |||||
**SH-21 | .219 | 7/32 | 5.6 | .205 | .018 | .007 | .196 | .015 | .074 | .338 | .324 | 284 | 110 | ||||
**SH-23 | .238 | 15/64 | 6.0 | .222 | .018 | .007 | .215 | .015 | .086 | .355 | .341 | 315 | 120 | ||||
SH-25 | .2S0 | 1/4 | 6.4 | .230 | .029 | + .003 -.000 | .010 | .225 | .025 | .21 | .45 | .43 | 599 | 175 | |||
SH-27 | .276 | 7.0 | .255 | ±.002 .002* | .029 | .010 | .250 | + .002 -.005 | .025 | .23 | .48 | .46 | 660 | 195 | |||
SH-28 | .281 | 9/32 | 7.1 | .261 | .029 | .010 | .256 | .025 | .24 | .49 | .47 | 670 | 200 | ||||
SH-31 | .312 | 5/16 | 7.9 | .290 | .029 | .011 | .281 | .025 | .27 | .54 | .52 | 751 | 240 | ||||
SH-34 | .344 | 11/32 | 8.7 | .321 | .029 | .011 | .309 | .025 | .31 | .57 | .55 | 812 | 2S5 | ||||
SH-35 | .354 | 9.0 | .330 | .029 | .012 | .320 | .025 | .35 | .59 | .57 | 832 | 300 | |||||
SH-37 | .375 | 3/8 | 9.5 | .352 | .029 | .012 | .338 | .025 | .39 | .61 | .59 | 883 | 320 | ||||
SH-39 | .394 | 10.0 | .369 | .029 | .012 | .354 | .025 | .42 | .62 | .60 | 954 | 335 | |||||
SH-40 | .405 | 13/32 | 10.3 | .382 | .029 | .012 | .366 | .025 | .43 | .63 | .61 | 964 | 350 | ||||
SH-43 | .438 | 7/16 | 11.1 | .412 | .029 | .013 | .395 | .025 | .50 | .66 | .64 | 1035 | 400 | ||||
SH-4GSP1 | .461 | 11.7 | .435 | .029 | .013 | .420 | .025 | .51 | .68 | .66 | 1110 | 460 | |||||
SH-46 | .459 | 15/32 | 11.9 | .443 | .029 | .013 | .428 | .025 | .54 | .68 | .66 | 1117 | 450 | ||||
SH-50 | .500 | 1/2 | 12.7 | .468 | ±.002 .004* | .039 | .016 | .461 | .035 | .91 | .77 | .74 | 1675 | 550 | |||
SH-55 | .551 | 14.0 | .519 | .039 | .016 | .509 | + .005 -.010 | .035 | .90 | .81 | .78 | 1800 | 600 | ||||
SH-56 | .562 | 9/16 | 14.3 | .530 | .039 | .016 | .521 | .035 | 1.1 | .82 | .79 | 1878 | 650 | ||||
SH-59 | .594 | 19/32 | 15.1 | .559 | + .003 .004* | .039 | .017 | .550 | .035 | 1.2 | .86 | .83 | 1979 | 750 | |||
SH-62 | .625 | 5/8 | 15.9 | .588 | .039 | .018 | .579 | .035 | 1.3 | .90 | .87 | 2091 | 800 | ||||
SH-6B | .669 | 17.0 | .629 | .039 | .020 | .621 | .035 | 1.4 | .93 | .89 | 2233 | 950 | |||||
SH-6B | .672 | 43/64 | 17.1 | .631 | .039 | .020 | .621 | .035 | 1.4 | .93 | .89 | 2233 | 950 | ||||
SH-68 | .688 | 11/16 | 17.5 | .646 | .046 | .021 | .635 | .042 | 1.8 | 1.01 | .97 | 3451 | 1000 | ||||
SH-75 | .750 | 3/4 | 19.0 | .704 | .046 | .023 | .693 | .042 | 2.1 | 1.09 | 1.05 | 3756 | 1200 | ||||
SH-78 | .781 | 25/32 | 19.3 | .733 | .046 | .024 | .722 | .042 | 2.2 | 1.12 | 1.08 | 3959 | 1300 | ||||
SH-61 | .812 | 13/16 | 20.6 | .762 | .046 | .025 | .751 | .042 | 2.5 | 1.15 | 1.10 | 4060 | 1450 | ||||
SH-B4 | .644 | 21.4 | .791 | .046 | .026 | .780 | .042 | 2.7 | 1.18 | 1.13 | 4200 | 1500 | |||||
SH-67 | .675 | 7/8 | 22.2 | .821 | .046 | .027 | .810 | .042 | 2.8 | 1.21 | 1.16 | 4365 | 1650 | ||||
SH-93 | 938 | 15/16 | 238 | .882 | 046 | 028 | .867 | .042 | 31 | 1 34 | 1 29 | 4720 | 1850 | ||||
SH-98 | .984 | 63/64 | 25.0 | .926 | .046 | .029 | .910 | .042 | 3.5 | 1.39 | 1.34 | 4923 | 2000 | ||||
SH-100 | 1.000 | 1 | 25.4 | .940 | .046 | .030 | .925 | .042 | 3.6 | 1.41 | 1.35 | 5024 | 2100 | ||||
SH-10Z | 1.023 | 26.0 | .961 | .046 | .031 | .946 | .042 | 3.9 | 1.43 | 1.37 | 5126 | 2250 | |||||
SH-106 | 1.062 | 1-1/16 | 27.0 | .998 | ±.004 .005* | .056 | + .004 -.000 | .032 | .982 | + .010 -.015 | .050 | 4.8 | 1.50 | 1.44 | 6293 | 2400 | |
SH-112 | 1.125 | 1-1/8 | 28.6 | 1.059 | .056 | .033 | 1.041 | .050 | 5.1 | 1.55 | 1.49 | 66SS | 2600 | ||||
**SIZES -12 THRU -23 STANDARD MATERIAL- CARBON STEEL; OPTIONAL MATERIAL- BERYLLIUM COPPER.
nnnn* F.I.M. {FULL INDICATOR MOVEMENT}- MAXIMUM ALLOWABLE DEVIATION OF CONCENTRICITY BETWEEN GROOVE & SHAFT.
nnnni BASED ON HOUSINGS/SHAFTS MADE OF COLD ROLLED STEEL. FOR AN EXPLANATION OF FORMULAS USED TO DERIVE THRUST LOAD
nnnnAND OTHER PERFORMANCE DATA CONTACT THE ROTOR CLIP ENGINEERING DEPARTMENT.
nnnn***F0R PLATED RINGS ADD .002" TO THE LISTED MAXIMUM THICKNESS. MAXIMUM THICKNESS WILL BE A MINIMUM OF .0002" LESS THAN THE
nnnnLISTED GROOVE WIDTH (W) MINIMUM.
nnnn20
nnnnFor the most up-to-date specifications, online ordering, quotations & sample orders, visit www.rotorclip.com
"
