MODEL 196ZPA MEDIUM DUTY ZERO PRESSURE LIVE ROLLER ACCUMULATOR0 pages

"MODEL 196ZPA MEDIUM DUTY ZERO PRESSURE LIVE ROLLER ACCUMULATOR nn

SPEED: 60 FPM, constant. PNEUMATIC ACTUATION: Maximum airline pressure should not exceed 30 PSI. FRL: Unit is provided with filter, regulator, lubricator with 1/4" ports. MOTOR DRIVE: 1/3 HP, 230/460/3,60 cycle, ODP right angle gear motor.

nn

OVERALL WIDTH

nn

ROLLER CHAIN:

nn

1 1/2" BETWEEN FRAMES 1 1/2"

nn

ELECTRICAL CONTROLS:

nn

1/4"

nn

Drive pulley is driven byNo. 50 roller chain for 1-1/2 HP or less and No. 60 chain on larger drives.
Chain take-up provided on motor base. Optional.

nn

Conveyor shown with optional supports

nn

7" "A" "A"

nn

Roach model 196ZPA accumulates packages quietly, safely and with zero back pressure. Loads up to 125
lbs./ft. may be effectively handled with its unique design.

nn

x zone length + 2' = overallconveyor length).

nn

6" 3" BELT WIDTH

nn

BEARINGS: All pulley bearings are precision, heavy duty, lubricated, ball
bearing units with cast iron housings.

LENGTH LENGTH >

nn

HP @60 FPM "A" MAX "B" MAX

12 12 " PRESSURE R PRESSURE R OLLERS OLLERS ZONE LENGTH ZONE LENGTH SENSOR R SENSOR R >

nn

ACCUMULATION:

OLLERS OLLERS TREAD R TREAD R >

nn

2'-0" long zones pneumatically actuated. by sensor rollers.
1'-0" of live roller over end plates at
each end of conveyor remains "live" during operation
(# of zones

OLLERS OLLERS 12 12 " >

nn

4" DRV. 8" DRV. 4" DRV. 8" DRV.1/316-5/8"17-5/8"58-5/32"58-5/32"

nn

BED: 7" x 1-1/2" x 12 ga. channelframe slotted for tread rollers to pop-out.
When unit is installed at 7'-0" elevation
or higher, rollers must be retained in conveyor frame. Specify desired elevation. Bed sections attached with
couplings and floor supports.

4" DIA. 4" DIA. RETURN RETURN 4" DIA. 4" DIA. >

nn

1/2 16-5/8" 17-5/8" 58-5/32" 58-5/32"3/417"17-5/8"58-25/32"58-25/32"

END PULLEY END PULLEY R OLLER OLLER END PULLEY END PULLEY 43 1/2" 43 1/2" 31 1/2" 31 1/2" 4" DIA. 4" DIA. T AKE-UP PULLEY AKE-UP PULLEY 4" OR 8" DIA. 4" OR 8" DIA. DRIVE PULLEY DRIVE PULLEY >

nn

1 17-1/4" 17-5/8" 59-17/32" 59-17/32"1-1/218-1/8"18-1/8"61-21/32"61-21/32"

"B" "B" >

nn

2 19" 19" 62-21/32" 62-21/32"

nn

SPECIFICATIONS TREAD ROLLERS: 1.9" dia. x 16 ga.steel, model 196S. PRESSURE ROLLERS: 1.9" dia. x 16 ga. steel, model 196S; 8" BF with 6" wide belt. BELTING: 6" wide black PVC-120 COS. DRIVE PULLEY: 4" dia. with 1-3/16" dia.shaft or 8" dia. with 1-7/16" dia. shaft,
both crowned and fully lagged. END PULLEY: 4" dia., crowned, with 1-3/16" dia. shaft. RETURN ROLLERS: 1.9" dia. x 16 ga.steel, model 196S, adjustable. SQUARING RODS: Adjustable rods onunderside of bed allow frame to be
squared for improved belt tracking and
are standard on all units over 30'.

nn

Pop-out rollers should be retained in frame if unitis elevated to 7'-0" and above.

nn34"