FPF2700 AccuPowerâ„¢ Advanced Load Management Products0 pages

January 2011
© 2010 Fairchild Semiconductor Corporation www.fairchildsemi.com
FPF2700 / FPF2701 / FPF2702 • Rev. 1.0.2
FPF2700 / FPF2701 / FPF2702 — AccuPower™ 0.4~2A Adjustable Over-Current Protection Load Switches
FPF2700 / FPF2701 / FPF2702 — AccuPower™ 0.4~2A
Adjustable Over-Current Protection Load Switches
Features
„X 2.8V to 36V Input Voltage Range
„X Typical RDS(ON)=88mƒÇ
„X 0.4A to 2A Adjustable Current Limit (Min.)
„X Slew Rate Controlled
„X ESD Protected, above 2000V HBM
„X Thermal Shutdown
„X Active LOW Enable
„X UVLO Protection
„X Power-Good Output
Applications
„X Motor Drives
„X Digital Cameras
„X Consumer Electronics
„X Industrial
„X Computing
„X Hard Disk Drives
„X Telecom Equipment
Figure 1. MLP (Top View) Figure 2. MLP (Bottom View)
Figure 3. SO8 (Top View)
Description
The AccuPower™ FPF270X series is a family of
current-limit load switches that provide full protection to
systems and loads from excess current conditions.
Minimum current limit is adjustable from 0.4A to 2.0A.
The FPF270X contains a slew-rate-controlled N-channel
MOSFET and slew-rated turn-on to prevent power bus
disturbances from being caused by “hot plugging” loads
or momentary excess load demands. The input voltage
range is 2.8V to 36V. Loads can be activated or
deactivated with a low-voltage logic-compatible ON pin.
Fault conditions can be monitored using the error flag
pin and/or the power-good pin.
Each member of the FPF270X family serves a category
of load-fault response. All devices clamp the load
current so that it cannot exceed an externally
programmed current level. An over temperature feature
provides further device protection in case of excessive
levels of power dissipation.
FPF2700 responds to an overload condition that lasts
longer than a fixed blanking period by turning off the
load, followed by a retry after the auto-restart time.
FPF2701 responds to an overload condition that lasts
longer than a fixed blanking period by latching off the
load. The load remains off unless either the ON pin is
toggled or the input voltage cycles through UVLO.
FPF2702 is intended to be used with external fault
management. Like the FPF2700 and FPF2701, it sets
the fault signal pin LOW when it activates current
clamping. This device is intended for applications where
external fault management coordinates the overload
response with the FPF2702.
The FPF270X is available in a space-saving Pb and
Halogen free, 8-lead MLP 3x3mm and SO8 packages.
Ordering Information
Part
Number Current Limit [A] Current Limit
Blanking Time [ms]
Auto-Restart
Time [ms]
ON Pin
Activity Package
FPF2700MPX 0.4 – 2.0 0.5 127.5 Active LOW MLP3X3
FPF2701MPX 0.4 – 2.0 0.5 NA Active LOW MLP3X3
FPF2702MPX 0.4 – 2.0 NA NA Active LOW MLP3X3
FPF2700MX 0.4 – 2.0 0.5 127.5 Active LOW SO8
FPF2701MX 0.4 – 2.0 0.5 NA Active LOW SO8
FPF2702MX 0.4 – 2.0 NA NA Active LOW SO8