ادامه
در صورتی که قیمت ارزی محصول را در اختیار دارید پس از عضویت و ورود به سایت می توانید فرم مربوطه را تکمیل و به همراه تصویر پرفورمای شرکت سازنده ارسال نمایید تا کارشناسان ما در اسرع وقت نسبت به محاسبه هزینه های حمل و ترخیص و صدور پیش فاکتور ریالی اقدام نمایند. هزینه استفاده از این سرویس برای هر درخواست 25 یورو می باشد. صنایع معظم در صورت تمایل به استفاده از این خدمات می توانند بدون نیاز به عضویت و پرداخت هزینه درخواست خود را به همراه کپی پرفورمای شرکت سازنده به ایمیل enquiry@iranindustryexpo.com و یا فاکس 88206264 بنام شرکت مهندسی و بازرگانی مشگاد ارسال نمایند.
در صورت عقد قرار داد مبلغ دریافتی به حساب خریدار عودت می شود.
ادامه
اگر مجموعه شما جزو صنایع مادر و معظم در فیلد پالایشگاه ، پتروشیمی ، حفاری ، نیروگاه ، معادن و فلزات ، خودروسازی ، تولید مواد غذایی و دارویی و.... می باشد لطفا درخواست خود را بر روی سربرگ به فاکس 88206264 و یا ایمیل enquiry@iranindustryexpo.com بنام شرکت مهندسی و بازرگانی مشگاد ارسال فرمایید.
کارشناسان این مجموعه در اسرع وقت با شما تماس خواهند گرفت .
بازدیدکننده محترم، از اینکه سایت ایران اینداستری را برای منابع یابی انتخاب کرده اید، از شما سپاسگزاریم.
اطلاعاتی برای نماینده شرکت Netplasmak Ltd. در ایران یافت نشد.
لطفا با انتخاب هر یک از بخش های فوق، درخواست خود را ارسال فرمایید تا توسط واحد بازرگانی ایران اینداستری اکسپو بررسی شود.
-
Semi-finished product:
for bubble wrap film
-
Treated material:
for PE
-
Type:
blown film
SHRINK FILM MACHINE
The extruder is a machine used to form polymer in a continuous manner. The raw material in the form of pellets is placed in a hopper that feeds the barrel. Barrel has a screw in it, driven by a motor and a gearbox. The screw transports and mixes polyethylene along the length of the barrel, which is heated to a temperature sufficient to melt the polymer. There are heaters and thermocouples along the barrel and on the die. Controllers that use thermocouples for feedback regulate the temperature along the barrel. At the end of the barrel, the material is forced out, through an orifice. Melt filters in here hold back impurities carried into the extruder with the plastic pellets and prevent the die from becoming blocked or damaged. Polyethylene film is usually produced by blown film extrusion. During blown film extrusion, the PE melt is forced through an annular die. Spiral mandrel dies with vertical orientation of the spirals are used for the production of polyethylene films. The bubble that is formed is inflated with air and hauled off at a higher speed than the die outlet speed. A current of air intensively cools the bubble. The bubble is then collapsed, trimmed if necessary, and rolled up using a suitable winding system. Polyethylene film rolls are then cut to the specified length. Therefore for manufacturing polyethylene bags, an extruder and a cutting machine are required.