High-Speed Programmable Controller DSP70000 pages

MAGTROL
DSP7000
Data Sheet
DSP7000 Series High-Speed Programmable - single channel
DSP7001
DSP7002 - dual channel
Dynamometer Controllers
FEATURES
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
•t
DSP7001 Single Channel: Low cost and easy to use
DSP7002 Dual Channel: Enables the support of
two testing instruments with independent or tandem
configurations and two fully independent control loops
Built-in Alarm System: For power, speed, torque,
temperature, air flow, water flow, electrical overload
and external inputs
High Speed Data Acquisition: Up to 500 torque and
speed points per second of both channels with time
stamp
High Quality, Easy-to-Read Vacuum Fluorescent
Readout: Displays torque, speed, power, auxiliary and
PID (proportional gain, integral and derivative) values
Fast Full-Curve Data Acquisition: Free-run to
locked rotor in seconds
Speed & Torque Operating Modes: PID settings for
exceptional dynamometer control
Programmable Digital PID Values: Controlled and
stored via M-Test Software or controlled manually
Built-in Current-Regulated Supply: For use with
Hysteresis Dynamometer or brakes up to 1amp
Adjustable Torque Units: English, Metric and SI are
standard
Digital Filter: Removes undesired noise from torque
signals
Saving: Currently used configuration can be saved and
recalled at power up
Single or Multi-point Torque and Speed Stabilized
Testing: Via M-TEST 7.0 Software
Closed Box Calibration
Rack Mounting: 19" (482.6 mm) with handles
Backwards Compatible: Compatible with the
DSP6001 (in DSP6001 mode)
HD5 dynamometers: Supported
USB: Standard
Low RPM: calculation from angle (quadrature signal)
and time designed to capture RPM’s as low as .001
RPM
Position Measurement: Two quadrature decoders
OPTIONS
•t
•t
1
Interfaces: RS-232 and IEEE-488
I/O card accessible programmatically (LabVIEW™,
Visual C)
DESCRIPTION
Magtrol’s Model DSP7000 High Speed Programmable
Dynamometer Controller employs state-of-the-art Digital
Signal Processing Technology to provide superior motor testing
capabilities. Designed for use with any Magtrol Hysteresis,
Eddy-Current or Powder Dynamometer, Magtrol In-Line
Torque Transducer or auxiliary instrumentation, the DSP7000
can provide complete PC control via the USB or optional
IEEE-488 or RS-232 interface. With up to 500 readings per
second, the DSP7000 is ideally suited for both the test lab and
the production line.
APPLICATIONS
In the laboratory, the DSP7000’s high sample rate provides
superior resolution for data acquisition and curve plotting.
This allows for capturing more usable motor test data during
switching, breakdown and other transitional areas of the
motor test curve. For production and incoming inspection,
the DSP7000 displays torque, speed and power at all times,
allowing the Controller to be used as a manual stand alone
unit or as part of a complete PC system.
MOTOR TESTING SOFTWARE
Magtrol’s M-TEST 7.0 Software (sold separately) is a stateof-the-art motor testing program for Windows®-based data
acquisition. Used with the Magtrol DSP7000 Controller,
Magtrol M-TEST 7.0 Software provides the control of any
Magtrol Dynamometer and runs test sequences in a manner
best suited to the overall accuracy and efficiency of the Magtrol
Motor Test System. The data that is generated by Magtrol’s
Motor Testing Software can be stored, displayed and printed
in tabular or graphic formats, and can be easily imported into
a spreadsheet.
Written in LabVIEW™, M-TEST 7.0 has the flexibility to
test a majority of motor types in a variety of ways. Because
of LabVIEW’s versatility, obtaining data from other sources
(e.g. thermocouples), controlling motor power and providing
audio/visual indicators is relatively easy.
Magtrol’s M-TEST 7.0 Software is ideal for simulating loads,
cycling the unit under test and motor ramping. Because it is
easy to gather data and duplicate tests, the software is ideal
for use in engineering labs, production testing and incoming/
outgoing inspection.
www.magtrol.com