"
MORBARK Beever M8D
®
™
Benefits
•t Perfect for rental yards, landscapers, golf courses and pruning crews, this
high-capacity unit is easy to transport and operate.
•t The only chipper in its class to combine both a wide infeed chute opening
and 1 ¼" thick chipping disc, the M8D has a 251-pound disc and shaft
weight provides more inertia to power through material and continuously
feed material.
•t With a single top feed wheel compression system and 32.3 ci hydraulic
motor with spring-assisted down pressure, the M8D generates more than
2,300 lb/ft of material pulling force and approximately 1,000 lb/ft of
combined down pressure to easily feed a variety of materials.
•t Like all Morbark equipment, the M8D is a long-lasting, durable machine
backed by a world-class parts and service support team.
Belt Drive
Infeed Chute
360° Swivel Discharge
Feed System
Direct drive with belt power transfer
eliminates clutch components and
over center belt tensioning systems,
reducing problem areas and easing
maintenance burdens.
Infeed chute with 96-cubic-inch
throat opening allows for easy
material feeding and reduced
trim labor and folds to reduce
transport and storage length.
360° swivel discharge with
adjustable chip deflector puts chips
right where they’re needed without
removing the Beever from the
tow vehicle.
A top feed wheel compression
system with spring-assisted down
pressure easily breaks down a
variety of materials.
Specifications
Specifications may vary with equipment options 5/14/12
General
Equipment Highlights
Additional Features
Chipping capacity . . . . . . . . . . . . . . . . . . . . 8"
Height . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7'4"
Width . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5'3"
Length (transport) . . . . . . . . . . . . . . . . 12'3 ½"
Length (operating) . . . . . . . . . . . . . . . . . . 14'3"
Gross weight . . . . . . . . . . . . . 2,150–2,750 lbs.
Suspension . . . . . . . . . . . . . . . 2,000 lb. torsion
Infeed opening . . . . . 33 ½" wide x 24 ¼" high
Throat opening . . . . . . . . . . 12" wide x 8" high
Feed wheel . . . . . . . 11 ½" wide x 9" diameter
Disc dimensions . . . 1 ¼" thick x 28" diameter
Engine . . . . . . . . . . . . . . . . . . Kohler or Kubota
Horsepower . . . . . . . . . . . . . . . . . . . 35–44 HP
Fuel capacity . . . . . . . . . . . . . . . . . . 10 gallons
Hydraulic capacity . . . . . . . . . . . . . . 10 gallons
Frame . . . . . . . . . . . . . . . . . . . . 2" x 4" Tubular
Tires . . . . . . . . . . . . . . . . . . . (2) 185/80Rx14"
Hitch . . . . . . . . . . . . . . . . . . . . . . . . . . . 2" Ball
Direct drive with belt power transfer
Fuel tank sight gauge, drain plug and
shut‑off valve
Automatic feed system
Chipper disc with two 10 ½" x 4" x 3/8"
dual‑edged chipper knives and four full-length,
bolt-on, chip throwing paddles
Hydraulic tank shut-off valve, drain plug,
clean-out cover and vented filter head assembly
with dipstick to check oil level
Reversible feed works control bar and dual safety
cables located within infeed chute
8D, 1400 CCA Battery
Options
Pinned chipper hood access with integrated hood
safety device to disconnect the start system when
the chipper hood is opened and allow ease of
disc maintenance.
Variable speed flow control
2,500 lb. Torflex suspension axle with electric
brake system, electric brake actuator and 185R14
tires with rims
Custom paint and logo packages
2 ½" lunet ring
Knife saver tool
Engine stop on infeed
Material pushing tool
Spanish and English safety decals
3" x 4" tubular steel fixed length drawbar and
3/8" thick safety chains with clasp hooks
Morthane Paint System: A chemically cured,
electrostatically applied urethane coating with
high-gloss finish, built-in UV protection, chip and
chemical resistance and corrosion protection
800.831.0042
989.866.2381
www.morbark.com
PO Box 1000
8507 S. Winn Rd.
Winn, MI 48896
"
عضویت 
ورود اعضا
راهنمای خرید
