Cetol WF 732 OilFinish0 pages

■n

limited dimension stir before u

stable wooden

constructions

/ater thinnable

sikkens

WOOD COATINGS

cleaning of

equipment with

Cetol WF 732 OilFinish

Product description Waterborne, translucent, deep matt wood oil as mid and finish coat for exterior and interior wooden constructions. Low

or medium build translucent natural effect varnish that emphasizes the wood structure.

- moisture permeability

- wood moisture regulating

- good leveling

- easy to apply

Colour With the choice of the different translucent colours, one should observe the Rosenheimer paint classification table. All

translucent colours can be mixed with each other. The optical appearence of different systems can differ depending on

substrate and wet film thicknesses, for this reason one should make trials before application.

Dark translucent colours give better weather durability than light colours. Colourless systems are not suitable for

exterior.

Timbers which contain extractives i.e. Oak, Larch or tropical woods can cause discolouring - these can appear after

weathering.

Translucent, colour tints i.e. from the Joinery Colour Collection.

Gloss level Deep matt

Binder type Acrylat with add on of natural oils

Packaging 20 L

Processing Spraying

Wet film thickness: 2 X 80-120um or 1 X 150 to 200um.

It is recommended to spray colour in two coats.

If coating twice, a midcoat denibbing should not be made

Because this product can be used for both semi- stable as well as stable wooden constructions, you apply two different

wet thicknesses. The colour intensity will vary.

Consumption 80 - 150 ml/m2, depending on applied wet thickness per coating, without losses.

Thinning If necessary with water max. 5 %.

Application temperature 15 - 25 °C for substrate, air and material at approx. 60 % R.H.

Drying times The drying process of the coating depends on the applied wet film thickness and can extend when using timber with a

high extract contents or drying in damp/cold conditions. During the drying process one should ensure for adequate

temperature and ventilation.

If the drying conditions are not upheld, damages within the coating cannot be warranted.

Drying at 23 °C / 50 % R.H.

Dust dry: after approx. 60 minutes

Recoatable: after approx. 4 - 6 hours waterborne

Cleaning of equipment Clean directly after use with water, if needed with washing up liquid or with ST 830.

StorageThe minimum storage stability of sealed containers is 2 years.

Storage temperature: +5 - +30 °C.

After ending of the storage time the product still can be usable, but some attributes may vary from new product.

Therefore such over-stored product has to be applied with special attention.

Opened cans must be sealed correctly! Store in a cool but frost-protected area.

Disposal Only residue emptied cans can be disposed via recycling. Liquid wastes must be disposed of according to national

regulations or according to EU-disposal key 08 01 12.

Hazard identification In accordance with EC guide lines - Material safety data sheet, point 15.

Warning Before use, read the identification and product information. Even when working with low emission products one should

take care of the customary protection measures.

General instructionsThe wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %.

According to the guidelines for window coating systems, published by the Federal German Committee for Paint and

Material Value Protection (Instruction Leaflet No. 18), of VOB, Parte, DIN 18363, and the recommendations of the

German Institute for Window Technology e.V. in Rosenheim, all wooden constructions in buildings must be coated on all

sides with at least one primer and one intermediate coat (minimum dry film thickness 30 urn) before they are

incorporated in buildings. The choice and use of the coating system, especially the colour shade, should also be taken

into account. Darker shades can increase the surface temperature (up to 80 C).

For use in a technical industrial companies and exclusively released for Sikkens systems recomondations.

VOC guideline EU limit value for this product (Kat. A/e): 150 g/l (2007)/130 g/l (2010). This product contains max. 80 g/l VOC.

Relevant information The here mentioned coating system is only an example, other systems are possible.

All external materials (i.e. fillers, tapes, sealing compounds, cleaners) must be checked for compatibility with the coating

system before use.

Please observe the relevant Technical Data Sheets or seek advice from the Sikkens sales representative or contact the

technical centre.

Coating recommendation Information on the maintenance coat:

Only waterborne coating systems may be used for the maintenance system!

Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ

Bus Pk

Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ

Bus Pk

Akzo Nobel Wood Coatings GmbH Diisseldorfer StraGe 96-100 40721 Hilden

AkzoNobel

United Kingdom Tel. +44 1254 687950 Fax. +44 1254 687960

Rep of Ireland Tel. +35 (0) 21 4220222 Fax. +35 (0) 21 4220205

Germany Tel.: +49-2103-77-800 Fax: +49-2103-77-577