Cetol WV 885 BPD+0 pages
stir before use
application by brush flow coating
DC
water thinnable store and transport store in a cool place cleaning of
uipment with gl<
limited din
stable wooden stable wooden
constructions constructions
protective Wear protecti
sikkens
WOOD COATINGS
Cetol WV 885 BPD+
Product description Waterborne impregnation (fluid timber protecting agent) for a protection against blue stain fungi and rot of none
staically subjected wooden constructions without earth contact (windows, shutters, pergola, claddings etc.), exterior.
- ready to use
- deep penetration
- good run-off properties
- neutral odour
The active substances are notified acc. guideline 98/8/EG and correspond to the specification EN 599 against blue stain
and rot fungi.
0,6 g/100 g propinylbutylcarbamate iodine
0,9 g/100 g propiconazol
0,3 g/100 g Tebuconazal
BAUA-register Nr. 40654
Wood protection agents must be registered according to the BPD. (BPD = Biocide Product Directive)
The examination follows the uptake value: 120-160 ml/m2 i.e. 123-164 g/m2 for timber in the resistance classes 3-5
Colorless
Acrylic Copolymer
2.5 I, 20 I, 120 I
Dipping, flooding, brushing
Working viscosity is approx. 11 seconds in a DIN cup 4 mm i.e. approx. 23 - 25 seconds in a ISO cup 3 mm at 20° C
material temperature.
50 - 160 ml/m2, depending on application method, type and absorption properties of wood (exact values must be
established through a sample)
Do not thin down
15 - 25 °C for substrate, air and material at approx. 60 % R.H.
Drying at 23 °C / 50 % R.H.
Dust dry: after approx. 60 minutes
Recoatable: after approx. 4 - 6 hours waterborne
Clean directly after use with water, if needed with washing up liquid or with ST 830.
A dipping tank containing material must be covered correctly and stirred or circulated regulary.
The minimum storage stability of sealed containers is 2 years.
Storage temperature: +5 - +30 °C.
After ending of the storage time the product still can be usable, but some attributes may vary from new product.
Therefore such over-stored product has to be applied with special attention.
Opened cans must be sealed correctly! Store in a cool but frost-protected area.
Only residue emptied cans can be disposed via recycling. Liquid wastes must be disposed of according to national
regulations or according to EU-disposal key 03 02 02.
In accordance with EC guide lines - Material safety data sheet, point 15.
The Impregnation serves as a protection of none statically subjected wooden constructions without earth contact,
exterior, against blue stain and rot according to DIN 68800, part 3.
Not for use with wood which has got direct contact with food or food preparation. Only for the use of qualified
enterprises
Dipping tanks or reservoirs: when using metal reservoirs, we recommend using None rusting steel i.e. V2A, the use of
other materials can lead to corrosion.
Biocide products must be handled carefully
Before use, read the identification and product information. Even when working with low emission products one should
take care of the customary protection measures.
Not to be used near waterways. The fluid must not entre water. Wood preservatives contain biozid substances for the
protection against pest control. They are only to be used according to instructions and in permitted working areas.
Misuse can lead to a hazard to health.
The wood moisture content for the application of Sikkens coating systems should be between 12 % and 15 %.
According to the guidelines for window coating systems, published by the Federal German Committee for Paint and
Material Value Protection (Instruction Leaflet No. 18), of VOB, Parte, DIN 18363, and the recommendations of the
German Institute for Window Technology e.V. in Rosenheim, all wooden constructions in buildings must be coated on all
sides with at least one primer and one intermediate coat (minimum dry film thickness 30 urn) before they are
incorporated in buildings. The choice and use of the coating system, especially the colour shade, should also be taken
into account. Darker shades can increase the surface temperature (up to 80 C).
For use in a technical industrial companies and exclusively released for Sikkens systems recomondations.
VOC guideline Out of scope.
Relevant information The the denibbing process may only be made after the following coating system.
The here mentioned coating system is only an example, other systems are possible.
Uptake consumption
Colour
Binder type
Packaging
Processing
Consumption
Thinning
Application temperature
Drying times
Cleaning of equipment
Storage
Disposal
Hazard identification
Warning
General instructions
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Industrial Coatings Ltd Unit 4a, Mercer Way, Shadsworth Blackburn, Lanes, BB12QZ
Bus Pk
Akzo Nobel Wood Coatings GmbH Diisseldorfer StraGe 96-100 40721 Hilden
AkzoNobel
United Kingdom Tel. +44 1254 687950 Fax. +44 1254 687960
Rep of Ireland Tel. +35 (0) 21 4220222 Fax. +35 (0) 21 4220205
Germany Tel.: +49-2103-77-800 Fax: +49-2103-77-577
"