ML200MHI0 pages

ML200MHI Series
Compact SMT, 2W
Medical Approved
DC/DC Converters
Electrical Specications
Specications typical @ +25°C, nominal input voltage & rated output current, unless otherwise noted. Specications subject to change without notice.

Key Features:
• 2W Output Power
• 4 kVAC rms Isolation

Input
Parameter

Conditions

Input Voltage Range

• Reinforced Insulation
• Compact SMT Case

Input Filter
Reverse Polarity Input Current
Leakage Current

• Single & Dual Outputs

Min.
Typ.
5 VDC Input
4.5
5.0
12 VDC Input 10.8
12.0
24 VDC Input 21.6
24.0
Internal Capacitor

Max.
5.5
13.2
26.4

Units

0.3
2.0

A
µA

Max.
±4.0
±1.0
±1.5

Units
%
%
%

150
200
15
±0.02

mV P - P
mV P - P
mV rms
%/°C

Typ.

Max.

15
80

20
100

Units
VAC rms
VPk
VAC
G⍀
pF
kHz

Typ.

Max.
+80
+90
+125

Units
°C
°C
°C

95

%

VDC

Output

• Low Leakage Current

• 2.0 MH MTBF
• Industry Standard Pin-Out
• EN 60950 Approved
• EN 60601 Approved

Parameter
Output Voltage Accuracy
Output Voltage Balance
Line Regulation
Load Regulation, See Note 1
Ripple & Noise (20 MHz), See Note 2
Ripple & Noise (20 MHz)
Ripple & Noise (20 MHz)
Temperature Coefcient
Output Short Circuit

Conditions

Min.

Typ.
±2.0
Dual Outputs, Balanced Loads
±0.1
Vin = Min to Max
±1.2
See Model Selection Guide
100
Over Line, Load & Temp.
±0.01
Momentary (0.5 Sec.)

General
Parameter
Isolation Voltage, Rated
Isolation Test Voltage
Reinforced Insulation Working Voltage
Isolation Resistance
Isolation Capacitance
Switching Frequency

Conditions
60 Seconds
Flash Tested For 1 Sec
500 VDC
100 kHz, 1V

Min.
4,000
6,000
300
10
50

Environmental

MicroPower Direct
292 Page Street
Suite D
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com

Parameter
Operating Temperature Range
Operating Temperature Range
Storage Temperature Range
Cooling
Humidity
Physical
Case Size
Case Material
Weight

Conditions
Ambient
Case

Min.
-25

-50
Free Air Convection
RH, Non-condensing

0.94 x 0.54 x 0.35 Inches (24.0 x 13.7 x 9.00 mm)
Non-Conductive Black Plastic (UL94-V0)
0.14 Oz (3.75g)

Reliability Specications
Parameter
MTBF
Safety Approvals
Moisture Sensitivity Level

Conditions
Min.
Typ.
Max.
MIL HDBK 217F, 25°C, Gnd Benign
2.0
UL 60601, UL 60950, EN 60601, EN 60950
IPC/JEDEC J-STD-020C Level 2

Units
MHours

Absolute Maximum Ratings
Parameter

Conditions

Input Voltage Surge (1 Sec)
Lead Temperature
Internal Power Dissipation

5 VDC Input
12 VDC Input
24 VDC Input
1.5 mm From Case For 10 Sec
All Models

Min.
-0.7
-0.7
-0.7

Typ.

Max.
9.0
18.0
30.0
260
650

Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.

www.micropowerdirect.com

Units
VDC
°C
mW